Laser cutting, laser etching, and other laser-related news, products, and resources.
This is papercut 83 of my papercutting quest (using the “922 Decorative Vector Ornaments” book, in preparation for incorporating them in future papercuts that are made by laser and also by hand.)
This is a very simple-looking design, but sometimes they are the hardest ones to make a decent job of cutting…
…but even close up I think this one actually looks OK. My skills really are (gradually) improving, as I get closer to the end of my 100-day challenge.
Papercut 082 : Oh dear! I’m in the process of changing over my website host, and have been a week without being able to access my blog.
I’ve moved the old pages and blog posts across to the new host, but there are still a lot of tweaks that I need to make in order to get the site fully working again.
In the meantime, I continued to do my papercuttings every day, so now (belatedly) I am finally able to update the website with my latest papercuttings:
Day 82 of my papercutting adventure (using the “922 Decorative Vector Ornaments” book).
It might not look it, but this was quite a tricky design to cut. The design involved having to leave just tiny links of paper in order to hold the actual physical piece of paper together. So the overall piece got very lacy and delicate towards the end.
I’d cut similar designs to this one earlier on in this project (i.e. even before starting this ‘100 days’ project), but I didn’t really like the results, before. However, now that I’m getting more proficient at cutting by hand (and also at adapting designs so that they can be cut out but still look fairly attractive), the end result is quite close to what I had imagined in the first place:
Plus, it’s another art nouveau-style design, so that quite appeals to me, and it also makes any mistakes less obvious because the curves and swirls in the design make it harder to spot.
This is papercut 81 of my papercutting adventure (using the “922 Decorative Vector Ornaments” book, in preparation for incorporating them in future papercuts that are made by laser and also by hand.)
I thought this design was going to be a pain in the butt to cut, but it turned out to be quite enjoyable and therapeutic because of the repetition and the challenging aspects to it:
First of all I cut the teeny tiny little dots out. They are approximately 1mm across, so it’s a miracle really that any of them look even vaguely round. Especially since the blade was getting quite blunt by then, so I was having to hack them out of the paper instead of cleanly slice them.
Then I did the sort of stacked-hearts shapes, by cutting the left-hand curves first then rotating the paper so I could move onto the next shape, etc.
And finally I did what should have been the easiest bit, which was the hole in the middle. Which is the bit that turned out looking the most wonky! Never mind – I can always tidy it up later, I suppose:
Day 80 of my papercutting adventure (using the “922 Decorative Vector Ornaments” book, in preparation for incorporating them in future papercuts that are made by laser and also by hand.)
Day 79 of my papercutting adventure (using the “922 Decorative Vector Ornaments” book, in preparation for incorporating them in future papercuts that are made by laser and also by hand.)
Day 78 of my papercutting adventure (using the “922 Decorative Vector Ornaments” book, in preparation for incorporating them in future papercuts that are made by laser and also by hand.)
Weirdly, I think I might be reaching a stage where I’ve come to a bit of a compromise with the perfectionist in me. The image below looks OK to me…
…but then close-up I can see all of the flaws in the cuts (that I couldn’t even see with my magnifying glasses when I was actually working on it!) But the perfectionist in me is now getting a tiny bit less uptight, so although the annoying imperfections do still leap out at me straight away, there is also a little part of me that goes “Hey! Nice leaves at the bottom!”, instead of “Oh no – the entire thing is a total mess.”
Day 77 of my papercutting adventure (using the “922 Decorative Vector Ornaments” book, in preparation for incorporating them in future papercuts that are made by laser and also by hand.)
Ha – I should have cut this one out last week for my birthday!
Day 76 of my papercutting adventure (using the “922 Decorative Vector Ornaments” book, in preparation for incorporating them in future papercuts that are made by laser and also by hand.)
Day 75 – I’m three quarters of the way through my papercutting adventure! (using the “922 Decorative Vector Ornaments” book, in preparation for incorporating them in future papercuts that are made by laser and also by hand.)
Not many mistakes on this one, and I like the swirly Art Nouveau-type design:
Here is something I’ve been playing with this week – the design of a laser-cut jewellery holder.
I made one for my mum last Christmas…
As you can see, it can hold lots of different types of jewellery (rings, necklaces, bracelets, watches, earrings). However, it still needs some tweaks.
As a very basic version though, this is the design that I used:
If you’ve got a laser cutter and you’d like to have a play with this design yourself, I’ve made a vector file available below.
(Click here for basic jewellery holder design for lasercutting)
Hope you found this post useful! If you think it might be of use to other makers/designers, please feel free to share the link to the post via Twitter (@LaserSister), Pinterest, Facebook (@LaserSister), etc…
